Structure Optimization of Connecting Tubes of Distributor for Improving the Distribution Uniformity of Refrigerant

Liu Lu; Liu Yantao; Zhan Feilong; Ding Guoliang; Gao Zheming; Xu Xuefei

doi:10.3969/j.issn.0253-4339.2022.01.151

您当前的位置：

首页 >

文章列表页 >

Structure Optimization of Connecting Tubes of Distributor for Improving the Distribution Uniformity of Refrigerant

更新时间：2024-07-18

- Structure Optimization of Connecting Tubes of Distributor for Improving the Distribution Uniformity of Refrigerant
- Journal of Refrigeration Vol. 43, Issue 1, (2022)
- 作者机构：
  
  1. 上海交通大学机械与动力工程学院
  2. 广东美的制冷设备有限公司
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0253-4339.2022.01.151
  CLC：
- Published：2022
- 稿件说明：
移动端阅览
Liu Lu, Liu Yantao, Zhan Feilong, et al. Structure Optimization of Connecting Tubes of Distributor for Improving the Distribution Uniformity of Refrigerant[J]. Journal of refrigeration, 2022, 43(1).
DOI：

Liu Lu, Liu Yantao, Zhan Feilong, et al. Structure Optimization of Connecting Tubes of Distributor for Improving the Distribution Uniformity of Refrigerant[J]. Journal of refrigeration, 2022, 43(1). DOI： 10.3969/j.issn.0253-4339.2022.01.151.

摘要

制冷空调系统采用多流路换热器时，要求制冷剂流量在各流路中均匀分配，其难以实现的主要原因之一是制冷剂流经折弯型分配器连接管时发生气液两相分离。本文提出将分配器连接管从一次折弯方式改为多次折弯方式的降低相分离程度的新思路，并用于连接管的结构优化设计。模拟研究了分配器连接管的折弯角度、折弯半径和管路直径对分流均匀性的影响；将这些结构参数进行合理组合，优化设计了具有多次折弯的分配器连接管结构；将该优化结构与原型结构进行分流不均匀度的对比。结果表明：分配器连接管的折弯角度是影响分流均匀性的最主要因素；与采用一次折弯的原设计相比，所设计的三次折弯型分配器连接管结构可降低分流不均匀度64.4%。

Abstract

Air conditioning systems commonly adopt multipath heat exchangers

which require distributors to guide the two-phase refrigerant to each flow path of heat exchangers uniformly. The gas-liquid two phase refrigerant may separate when it flows through the connecting tubes of distributors with bends

resulting in the deterioration of distribution uniformity. In this study

an optimization method was proposed for changing the traditional single-bending of tubes to the multi-bending of tubes to reduce the degree of separation of the gas-liquid two phase refrigerant. First

the influence of the bending structure factors of the connecting tubes on the distribution uniformity was investigated

including the bending angle

bending radius

and tube diameter. Second

the optimized structural parameters of the bending angle

bending radius

and tube diameter were combined to design an optimized connecting tube for the distributor. Finally

the distribution unevenness was compared between the optimized and original connecting tubes of the distributor. The results from the case studies in this study show that the bending angle is the main influencing factor

and the proposed optimization connecting tube of the distributor with three bends can reduce the distribution unevenness by 64.4% compared with the original one with a single bend.

关键词

Keywords

references

Views

1534

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Experimental Comparison on Distribution Uniformity Among Different Types of Refrigerant Distributors Used in Air-conditioners

Distribution Performance Assessment and Structure Optimization of Distributor Applied in Small-diameter Air Conditioner

Related Author

Liu Lu

Meng Jianjun

Shi Lihua

Wang Qingjie

Gao Yang

Weng Xiaomin

Ding Guoliang

Hu Haitao

Related Institution

Qingdao Hisense Hitachi Air Conditioning Systems Co., Ltd.

Institute of Refrigeration and Cryogenics, Shanghai Jiao Tong University

International Copper Association

Address：10/F, Yindu Mansion, 67 Fucheng Road, Haidian Dist, Beijing, China Postal code：100142
Tel：010-68711412 Email：editor@car.org.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09064830号-19 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰