Simulations on a Water Circulating System for a Large-scale Irregular Chamber with Internal Heat Sources for High-precision Temperature Control

Xue Yu; Ye Wei; Zhao Wenxuan; Wu Chao; Zhang Xu

doi:10.3969/j.issn.0253-4339.2021.02.100

您当前的位置：

首页 >

文章列表页 >

Simulations on a Water Circulating System for a Large-scale Irregular Chamber with Internal Heat Sources for High-precision Temperature Control

更新时间：2024-07-18

- Simulations on a Water Circulating System for a Large-scale Irregular Chamber with Internal Heat Sources for High-precision Temperature Control
- Journal of Refrigeration Vol. 42, Issue 2, (2021)
- 作者机构：
  
  1. 同济大学机械与能源工程学院
  2. 同济大学工程结构性能演化与控制教育部重点实验室
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0253-4339.2021.02.100
  CLC：
- Published：2021
- 稿件说明：
移动端阅览
Xue Yu, Ye Wei, Zhao Wenxuan, et al. Simulations on a Water Circulating System for a Large-scale Irregular Chamber with Internal Heat Sources for High-precision Temperature Control[J]. Journal of refrigeration, 2021, 42(2).
DOI：

Xue Yu, Ye Wei, Zhao Wenxuan, et al. Simulations on a Water Circulating System for a Large-scale Irregular Chamber with Internal Heat Sources for High-precision Temperature Control[J]. Journal of refrigeration, 2021, 42(2). DOI： 10.3969/j.issn.0253-4339.2021.02.100.

摘要

用以测量辐射信号的球形实验装置置于直径为43 m、高为44 m的圆柱形实验厅内，球体外侧安装信号接收光电倍增管球壳层（PMTs），其运行会产生200 kW的高热。为维持球体表面水体温度稳定在（21±1）℃高精度恒温环境下，本文采用计算流体力学（CFD）技术，将球体浸没在循环水中并配合上下两段式布水方式进行精准控温。结果表明：上下两段布水方式可实现大型水体空间局部精确控温。考虑到不规则腔体流道限制，设计调整水循环布水角度，上布水口低温面积最大增幅达20%；提出增大上下布水器水量比以控制水体垂直温差，上下布水器水量之比为2.5:1时控温能力最强，且降温最有效的区域是多孔介质PMT层与外水层；为得到不同热量下温度分布的统一规律，增大热源发热量，内水层上下布水口低温面积变化幅度有差异，上布水口低温面积缩小41%，下布水口缩小62%，但下布水口低温面积始终大于上布水口。

Abstract

A spherical experimental device placed in a cylindrical hall of diameter 43 m and height 44 m was used to measure the radiation signal. Photomultiplier tubes (PMTs)

which is used to receive the signal

were installed on the exterior surface of the sphere. The PMTs generated heat at 200 kW during operation. To maintain the surface temperature of the sphere at (21±1) ℃

a method for high-precision temperature control by immersing the sphere in circulated water and distributing water up and down simultaneously was proposed. A simulation method using computational fluid dynamics was applied to analyze the temperature field of the water. The results showed that the method of distributing water up and down simultaneously can achieve a precise local temperature control in large spaces. Owing to the limited flow channels in the irregular cavity

the angle of inclination for both upward and downward water distributors of the circulating system was adjusted to improve the performance of temperature control locally. The increase in the area with a low temperature using the upper water distributors can be up to 20%. To reduce the vertical temperature difference of the water

the water flow ratio of the upper and lower water distributors was increased. The temperature requirement can be met when the water flow ratio is 2.5:1.The water volumes that are effectively cooled are the porous media layer and outer water layer. To obtain temperature profiles with an accuracy of (21±1) ℃ under various heating intensities

the heat flux of the heating sources was determined. The variation ranges of the low-temperature volumes around the upper water distributors differed from that around lower water distributors of the inner water layer. The low-temperature volumes around the water distributors at the top decreased by 41%

while the volumes around the distributors at the bottom decreased by 62%. However

the low-temperature volumes around the lower water distributors were larger than those at the upper water distributor

regardless of the amount of heat flux from the heating sources.

关键词

Keywords

references

Views

1847

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Heat Storage and Discharge Characteristics of Flat Filling Phase Change Thermal Energy Storage Tank

Thermal Resistance Analysis and Numerical Optimization of Mechanical Expanded Tube-to-Fin Joints

Design of High Efficiency Cooler for IGBT Module in CRH2

Dynamic identification method for flow patterns of liquid-solid two-phase flow in horizontal pipelines

^1,2^1,2<p>Analysis of TheInfluence of Refrigerant Phase Transition on The Temperature Control of LargeCapacity Lithium-ion Battery<br></p>

Related Author

Liu Hanyi

Zhang Liang

Yang Yang

Cao Jiayuan

Li Sisi

Ouyang Xinping

Xia Rongxin

Li Donglei

Related Institution

School of Energy and Power Engineering, University of Shanghai for Science and Technology

Institute of Refrigeration and Cryogenics, University of Shanghai for Science and Technology

National Virtual Simulation Experimental Teaching Center for Building EnergySchool of Environmental and Energy Engineering

Beijing University of Civil Engineering and Architecture

Guangzhou Metro Design institute construction Drawing consuiting co. Ltd

Address：10/F, Yindu Mansion, 67 Fucheng Road, Haidian Dist, Beijing, China Postal code：100142
Tel：010-68711412 Email：editor@car.org.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09064830号-19 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰