Study on the Flow Field of Hydrostatic Cavity of Impinging Freezer with Different Sizes by CFD

Gu Hanwen; Xie Jing; Wang Jinfeng

doi:10.3969/j.issn.0253-4339.2020.04.097

您当前的位置：

首页 >

文章列表页 >

Study on the Flow Field of Hydrostatic Cavity of Impinging Freezer with Different Sizes by CFD

更新时间：2024-07-18

- Study on the Flow Field of Hydrostatic Cavity of Impinging Freezer with Different Sizes by CFD
- Journal of Refrigeration Vol. 41, Issue 4, (2020)
- 作者机构：
  
  1. 上海水产品加工及贮藏工程技术研究中心
  2. 上海冷链装备性能与节能评价专业技术服务平台
  3. 上海海洋大学食品学院
  4. 食品科学与工程国家级实验教学示范中心(上海海洋大学
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0253-4339.2020.04.097
  CLC：
- Published：2020
- 稿件说明：
移动端阅览
Gu Hanwen, Xie Jing, Wang Jinfeng. Study on the Flow Field of Hydrostatic Cavity of Impinging Freezer with Different Sizes by CFD[J]. Journal of refrigeration, 2020, 41(4).
DOI：

Gu Hanwen, Xie Jing, Wang Jinfeng. Study on the Flow Field of Hydrostatic Cavity of Impinging Freezer with Different Sizes by CFD[J]. Journal of refrigeration, 2020, 41(4). DOI： 10.3969/j.issn.0253-4339.2020.04.097.

摘要

为进一步优化上下冲击式速冻机的冻结效果，本文以静压腔尺寸为4 m×1.5 m×2 m的实体速冻机为基础，保证入口压力为190 Pa、入口体积流量为2.64 m3/s不变，提出了4 m×1.5 m×1.5 m、4 m×2 m×1.5 m、4 m×2 m×2 m、4 m×2.5 m×1.5 m、4 m×2.5 m×2 m等5种不同的静压腔尺寸，通过CFD来模拟静压腔尺寸变化对于速冻机内部流场的改变，从速冻机喷嘴出口风速、钢带表面气流的矢量分布、钢带表面换热强度及换热均匀性等方面来综合分析静压腔内部换热特性。结果表明：在静压腔入口流量相同、压力不变的情况下，唯有4 m×1.5 m×1.5 m的出口风速与原有尺寸的出口风速相差较小，其余尺寸的出口风速略小但变化幅度不明显。而该尺寸的换热强度以及换热均匀性却远不如4 m×2.5 m×1.5 m、4 m×2.5 m×2 m。此外，静压腔尺寸为4 m×2 m×2 m的换热强度虽然比4 m×1.5 m×2 m的换热强度高约4.85%，但均匀性较差，不足以成为优选设计。4 m×2.5 m×1.5 m与4 m×2.5 m×2 m的换热强度达到177.76和177.39，比原有尺寸下钢带表面换热强度高约6.81%和6.59%，且均匀性也为最佳。结合上述因素，4 m×2.5 m×1.5 m和4 m×2.5 m×2 m在出口风速、换热强度及均匀性方面均为5种尺寸中最优的设计。

Abstract

Since traditional impact freezers have low freezing efficiency and high food weight loss

upper and lower impact freezers have gradually been recognized as new types with high efficiency by the food quick-freezing industry. In order to further optimize the freezing effect of the upper and lower impact freezers

a solid impact freezer with a hydrostatic cavity size of 4 m × 1.5 m × 2 m was taken as the baseline. The internal flow fields of five different dimensions of hydrostatic cavities including 4 m × 1.5 m ×1.5 m

4 m × 2 m × 1.5 m

4 m × 2 m × 2 m

4 m × 2.5 m × 1.5 m

and 4 m × 2 m × 2 m were simulated by computational fluid dynamics (CFD) with the inlet pressure of 190 Pa and inlet flow rate of 4.4 m3/s. The internal heat transfer characteristics of the hydrostatic cavity were also analyzed comprehensively in terms of the nozzle outlet wind velocity of the impact freezer

vector distribution of the air flow on the surface of the steel belt

surface heat transfer intensity and heat transfer uniformity of the steel belt. The results showed that under the condition of the same inlet flow and constant pressure

only the outlet wind velocity of the cavity of dimensions 4 m × 1.5 m × 1.5 m differed slightly from that of the original size

and the wind velocities of the other sizes were slightly lower

but the range of change was not apparent. However

the heat transfer intensity and uniformity of this size were far less than those for the cavities with dimensions of 4 m × 2.5 m × 1.5 m and 4 m × 2.5 m × 2 m. In addition

although the heat transfer intensity of the hydrostatic cavity of dimensions 4 m × 2 m × 2 m was approximately 4.85% higher than that of the cavity of dimensions 4 m × 1.5 m × 2 m

its uniformity was poor and insufficient for it to be the optimal design. The heat transfer intensity of the cavities of dimensions 4 m × 2.5 m × 1.5 m and 4 m × 2.5 m × 2 m reached 177.76 and 177.39

which were approximately 6.81% and 6.59% higher than the surface heat transfer intensity of the steel belt under the original size. Additionally

the uniformity was the best. Combined with the above factors

the cavities of dimensions 4 m × 2.5 m × 1.5 m and 4 m × 2.5 m × 2 m were the optimal designs among the five sizes in terms of the outlet wind velocity

heat transfer intensity

and uniformity.

关键词

Keywords

references

Views

1810

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Effect of Slit Nozzles of Different Structures on the Heat Transfer of Impinging Jets

Calculating Method and Experimental Verification of Freezing Time of Frozen Food by Liquid Nitrogen

Heat Transfer Research on Food Frozen by Cryogenic Liquid Nitrogen

Effects of Cooling Rate on the Structure of Onion Epidermal Cells

Optimization of Air Flow Pattern for Leakage of Ammonia Gas in a Refrigerator Room

Related Author

Shu Zhitao

Xie Jing

Yang Dazhang

Liang Yaying

Xu Xiaojin

Liu Jianhua

Zhou Xiaoqing

Liu Jianhua

Related Institution

Shanghai Professional Technology Service Platform on Cold Chain Equipment Performance and Energy Saving Evaluation, Shanghai Engineering Research Center of Aquatic Product Processing & Preservation, College of Food Science and Technology, Shanghai Ocean University

School of Energy and Power Engineering, University of Shanghai for Science and Technology

Shanghai Key Laboratory of Multiphase Flow and Heat Transfer in Power Engineering

NO.704, CSIC

Tianjin Key Laboratory of Refrigeration Technology, Tianjin University of Commerce

Address：10/F, Yindu Mansion, 67 Fucheng Road, Haidian Dist, Beijing, China Postal code：100142
Tel：010-68711412 Email：editor@car.org.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09064830号-19 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰