Thermal Resistance Analysis and Numerical Optimization of Mechanical Expanded Tube-to-Fin Joints

Li Sisi; Ouyang Xinping; Xia Rongxin; Li Donglei

doi:10.3969/j.issn.0253-4339.2020.03.038

您当前的位置：

首页 >

文章列表页 >

Thermal Resistance Analysis and Numerical Optimization of Mechanical Expanded Tube-to-Fin Joints

更新时间：2024-07-18

- Thermal Resistance Analysis and Numerical Optimization of Mechanical Expanded Tube-to-Fin Joints
- Journal of Refrigeration Vol. 41, Issue 3, (2020)
- 作者机构：
  
  上海理工大学制冷及低温工程研究所
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0253-4339.2020.03.038
  CLC：
- Published：01 January 2020
- 稿件说明：
移动端阅览
Li Sisi, Ouyang Xinping, Xia Rongxin, et al. Thermal Resistance Analysis and Numerical Optimization of Mechanical Expanded Tube-to-Fin Joints[J]. Journal of refrigeration, 2020, 41(3).
DOI：

Li Sisi, Ouyang Xinping, Xia Rongxin, et al. Thermal Resistance Analysis and Numerical Optimization of Mechanical Expanded Tube-to-Fin Joints[J]. Journal of refrigeration, 2020, 41(3). DOI： 10.3969/j.issn.0253-4339.2020.03.038.

摘要

本文采用有限元模拟方法，得到套片式翅片管换热器机械胀接的翅片与基管间的胀后节点接触应力分布。提出模拟的总体接触应力并不是节点接触应力算术平均的观点和一种较为合理的计算方法。对一种套片式换热器试件进行传热性能实验以获取翅片与基管之间的接触热阻数值，由模拟计算的总体接触应力与实验接触热阻数值，计算两者的关联式。采用有限元模拟方法预测各种胀接量下的总体接触应力及最优的胀接尺寸，利用弹塑性理论计算对比模拟计算进行相互验证。结果发现，材料弹塑性理论计算结果与模拟计算结果的相对偏差为7.3%，偏差较小，证明两者均具有效性。

Abstract

The finite element simulation method was used to obtain the distribution of contact stress between the fin and the base pipe. It is proposed that the overall contact stress is not just the average value of the node contact stress

and a more reasonable method of calculation method is proposed. A heat transfer performance test of a sleeve-type heat exchanger was undertaken to determine the contact thermal resistance between the fin and the base pipe. The correlation between the overall contact stress and the contact thermal resistance was established. The finite element simulation method was used to determine the overall contact stress under various expansion factors

and to determine the optimal process dimension. Finally

the contact stress value calculated by the elastoplastic theory was used for internal verification. The relative deviation between the contact stress calculated using elastoplastic theory and the simulated value was small (7.3%).

关键词

Keywords

references

Views

2349

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Heat Storage and Discharge Characteristics of Flat Filling Phase Change Thermal Energy Storage Tank

Research Status of Microchannel Heat Dissipation Technology Based on Porous Structure

Design of High Efficiency Cooler for IGBT Module in CRH2

Dynamic identification method for flow patterns of liquid-solid two-phase flow in horizontal pipelines

^1,2^1,2<p>Analysis of TheInfluence of Refrigerant Phase Transition on The Temperature Control of LargeCapacity Lithium-ion Battery<br></p>

Related Author

Liu Hanyi

Zhang Liang

Yang Yang

Cao Jiayuan

Zhou Xiong

Zhang Li

Gao Feng

Zhang Yi

Related Institution

School of Energy and Power Engineering, University of Shanghai for Science and Technology

School of Mechanical and Power Engineering, East China University of Science and Technology

National Virtual Simulation Experimental Teaching Center for Building EnergySchool of Environmental and Energy Engineering

Beijing University of Civil Engineering and Architecture

Guangzhou Metro Design institute construction Drawing consuiting co. Ltd

Address：10/F, Yindu Mansion, 67 Fucheng Road, Haidian Dist, Beijing, China Postal code：100142
Tel：010-68711412 Email：editor@car.org.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09064830号-19 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰