Effect of Air Duct Layout on Airflow in Data Center Using Under-floor Air Distribution (1) Numerical Design

doi:10.3969/j.issn.0253-4339.2018.02.080

您当前的位置：

首页 >

文章列表页 >

Effect of Air Duct Layout on Airflow in Data Center Using Under-floor Air Distribution (1) Numerical Design

更新时间：2024-07-18

- Effect of Air Duct Layout on Airflow in Data Center Using Under-floor Air Distribution (1) Numerical Design
- Journal of Refrigeration Vol. 39, Issue 2, (2018)
- 作者机构：
  
  1. 江苏省能源系统过程转化与减排技术工程实验室南京师范大学能源与机械工程学院
  2. 江苏省能源系统过程转化与减排技术工程实验室,南京师范大学能源与机械工程学院
  3. 江苏省邮电规划设计院有限责任公司
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0253-4339.2018.02.080
  CLC：
- Published：2018
- 稿件说明：
移动端阅览
Effect of Air Duct Layout on Airflow in Data Center Using Under-floor Air Distribution (1) Numerical Design[J]. Journal of refrigeration, 2018, 39(2).
DOI：

Effect of Air Duct Layout on Airflow in Data Center Using Under-floor Air Distribution (1) Numerical Design[J]. Journal of refrigeration, 2018, 39(2). DOI： 10.3969/j.issn.0253-4339.2018.02.080.

摘要

本文以排布奇数列机柜冷通道封闭的数据中心子模块为研究对象（3列机柜为例），采用CFD模拟将静压层高度与地板穿孔率对数据中心气流组织的联合影响进行可视化，并分析了两种参数组合的25个典型模型的温度场，选出最佳静压层高度与地板穿孔率的范围分别为600~700 mm，20%~50%。对比了最佳静压层高度与地板穿孔率组合范围内的8个数据中心气流组织模型，选出机柜内部温度分布较均匀的气流组织模型。在此基础上，在静压层内架设挡板，并在﹣15°~45°的挡板角度中选择最佳角度以获得最优冷却效果。结果表明：静压层高度为600 mm，穿孔地板穿孔率为20%，设置15°挡板的数据中心子模块为最优模型。

Abstract

A sub-module (three-row cabinet as an example) of data center with the cold channel closed in an array of odd-numbered columns is taken as the subject to be investigated. A computational fluid dynamics simulation was used to visualize the compound effect of the plenum height and floor perforation rate on the airflow in the data center. The temperature fields of 25 typical models with various combinations of plenum heights and floor perforation rates were analyzed to find the best match of 600-700 mm (plenum height) and 20%–50% (perforation rate). Furthermore

eight plenum height and perforation rate models that fell within the above range were compared to find the best uniform temperature distribution inside the cabinets. Based on the results

a baffle was erected in the plenum at four angles from -15° to 45° to obtain the most satisfying cooling effect. The results showed that the optimal model for the data center sub-module had a plenum height of 600 mm

perforation rate of 20%

and 15° baffle.

关键词

Keywords

references

Views

2389

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Effect of Air Duct Layout on the Airflow in Data Center Using Under-floor Air Distribution (2) Experimental Verification

Cooling System for Data Centers Based on the Air-Water-Air Principle with Increased Temperature Differential

Scenario Analysis of Data Centers in China Under Carbon Neutrality Target

Performance of Cooling and Heating System with Dual-Evaporating Temperature and Mechanical Subcooling Using CO₂ for Data Centers

Load Characteristics Analysis of Water-Source Heat Pump System for Harvesting Waste Heat from Small Data Centers

Related Author

胡雨

耿云

张忠斌

张萌

姚喻晨

黄虎

Jing Yang

Xie Xiaoyun

Related Institution

南京师范大学能源与机械工程学院江苏省能源系统过程转化与减排技术工程实验室

南京师范大学能源与机械工程学院江苏省能源系统过程转化与减排技术工程实验室，江苏省邮电规划设计院有限责任公司

Building Energy Research Center, Tsinghua University

Department of Refrigeration and Cryogenic Engineering, Beijing University of Technology

Tianjin Key Laboratory of Refrigeration Technology, Tianjin University of Commerce

Address：10/F, Yindu Mansion, 67 Fucheng Road, Haidian Dist, Beijing, China Postal code：100142
Tel：010-68711412 Email：editor@car.org.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09064830号-19 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰