Investigation on Thermal Conductivity of Ni-P-PTFE Composite Coating on Copper Tubes

He Kailong; ChenYing; Zhong Tianming; Mo Songping

doi:10.3969/j.issn.0253-4339.2013.01.084

您当前的位置：

首页 >

文章列表页 >

Investigation on Thermal Conductivity of Ni-P-PTFE Composite Coating on Copper Tubes

更新时间：2024-07-18

- Investigation on Thermal Conductivity of Ni-P-PTFE Composite Coating on Copper Tubes
- Journal of Refrigeration Vol. 34, Issue 1, (2013)
- 作者机构：
  
  广东工业大学材料与能源学院
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0253-4339.2013.01.084
  CLC：
- Published：2013
- 稿件说明：
移动端阅览
He Kailong, ChenYing, Zhong Tianming, et al. Investigation on Thermal Conductivity of Ni-P-PTFE Composite Coating on Copper Tubes[J]. Journal of refrigeration, 2013, 34(1).
DOI：

He Kailong, ChenYing, Zhong Tianming, et al. Investigation on Thermal Conductivity of Ni-P-PTFE Composite Coating on Copper Tubes[J]. Journal of refrigeration, 2013, 34(1). DOI： 10.3969/j.issn.0253-4339.2013.01.084.

摘要

采用Ni-P-PTFE化学复合镀对管进行表面处理能有效减少污垢在换热表面上形成。然而，在实际应用上，复合镀层对管导热性能的影响是必须考虑的问题。实验利用热阻法对基Ni-P-PTFE复合镀层的导热系数进行测量，并利用Wilson plot方法处理数据最终得到Ni-P-PTFE复合镀层的导热系数。分析了镀层各组分镍(Ni)，聚四氟乙烯(PTFE)，碳(C)，磷(P)的质量分数对其导热性能的影响规律。结果表明，Ni-P-PTFE复合镀层的导热系数随PTFE和P的质量分数增大而降低，随C的质量分数增加而增大。当PTFE，C以及P的质量分数w(PTFE)=1.76%，w(C)=3.82%和w(P)=10.81%时，最大值为23.12 W/(m.K)。尽管复合镀层的导热系数不高，但由于其厚度很小，镀层产生的热阻仅为9.91×10-5~1.6×10-4 (m2.K)/W，所以复合镀层í?管仍保持很高的导热系数值314.88~357.55W/(m.K)。

Abstract

Copper tubes covered by Ni-P-PTFE composite coating can mitigate fouling adhesion on the heat exchange surface. However

the impact of composite coating on the thermal conduction of copper tubes should be considered. A thermal resistance method was utilized to measure the heat transfer coefficient of copper tubes with Ni-P-PTFE composite coatings. The thermal conductivities of these Ni-P-PTFE composite coatings were gained by means of Wilson plot in the end. The effects of Ni

PTFE

C and P contents were discussed on the thermal conductivity of Ni-P-PTFE composite coating. The results showed the thermal conductivity of these Ni-P-PTFE composite coatings were weakened by the increases of PTFE and P contents

but enhanced when the C content increased. It reached a peak value 23.12 W/(m.K) when w(PTFE)=1.76%

w(C)=3.82% and w(P)=10.81%

respectively. Although the thermal conductivities of the composite coatings were lower

their thermal resistances in the total heat transfer process were from 9.91×10-5 to 1.6×10-4(m2.K)/W due to their small thickness. Therefore

the tubes with Ni-P-PTFE composite coatings still kept high thermal conductivities 314.88~357.55W/(m.K).

关键词

Keywords

references

Views

2088

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Investigation on Anti-fouling Capacity and Thermal Conductivity of Ni-P-PTFE Composite Coating

Application of Inverse Problem Method in Investigation of Thermal Conductivity for PCMs

Study on Thermal Conductivities of CaCl2/ENG Composite Adsorbents

Research Progress of Phase Change Materials for Cold Thermal Energy Storage in Air-conditioners

Related Author

Wang Yongzhen

Chen Ying

Luo Xianglong

Gong Yulie

Yuan Yanping

Du Yanxia

Cheng Baoyi

Gao Jiao

Related Institution

Guangzhou Institute of Energy Conversion, Chinese Academy of Science

Southwest Jiaotong University

The College of Mechanical and Electrical Engineering, QUST University

School of Energy and Environment, Southeast University

Address：10/F, Yindu Mansion, 67 Fucheng Road, Haidian Dist, Beijing, China Postal code：100142
Tel：010-68711412 Email：editor@car.org.cn
Technical support is provided by Beijing Founder electronics co., LTD 京ICP备09064830号-19 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰